Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A M349500

Cone Part Number

 N/A M349546XX

Cup Part Number

 N/A M349511

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 10.0630 in255.600 mm

D - Cup Outer Diameter

 N/A 13-1/2 in342.900 mm

B - Cone Width

 N/A 2.5 in63.5 mm

C - Cup Width

 N/A 1.7500 in44.450 mm

T - Bearing Width

 N/A 2.2500 in57.150 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.06 in1.5 mm
r - Cup Backface "To Clear" Radius2 N/A 0.130 in3.30 mm

da - Cone Frontface Backing Diameter

 N/A 10.63 in270 mm

db - Cone Backface Backing Diameter

 N/A 10.63 in270 mm

Da - Cup Frontface Backing Diameter

 N/A 13.15 in333.00 mm

Db - Cup Backface Backing Diameter

 N/A 12.68 in322.07 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.04 in1 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.08 in2 mm
a - Effective Center Location3 N/A 0.1 in2.5 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 36600 lbf163000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 141000 lbf628000 N

C0 - Static Radial Rating

 N/A 286000 lbf1270000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 21800 lbf96800 N

Factors

K - Factor7 N/A 1.68
e - ISO Factor8 N/A 0.35
Y - ISO Factor9 N/A 1.73
Cg - Geometry Factor10 N/A 0.143
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.