Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 30230M

Cone Part Number

 N/A X30230M

Cup Part Number

 N/A Y30230M

Design Unit

 N/A Metric

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A 30230M-90KM1

Dimensions

d - Bore

 N/A 150 mm5.9055 in

D - Cup Outer Diameter

 N/A 270 mm10.6299 in

B - Cone Width

 N/A 45 mm1.7717 in

C - Cup Width

 N/A 38 mm1.4961 in

T - Bearing Width

 N/A 49.000 mm1.9291 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 4.060 mm0.16 in
r - Cup Backface "To Clear" Radius2 N/A 3.05 mm0.12 in

da - Cone Frontface Backing Diameter

 N/A 168 mm6.61 in

db - Cone Backface Backing Diameter

 N/A 174 mm6.85 in

Da - Cup Frontface Backing Diameter

 N/A 250.44 mm9.86 in

Db - Cup Backface Backing Diameter

 N/A 245.11 mm9.65 in

Ab - Cage-Cone Frontface Clearance

 N/A 8.9 mm0.35 in

Aa - Cage-Cone Backface Clearance

 N/A 3.6 mm0.14 in
a - Effective Center Location3 N/A 3.6 mm0.14 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 146000 N32900 lbf
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 565000 N127000 lbf

C0 - Static Radial Rating

 N/A 735000 N165000 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 109000 N24500 lbf

Factors

K - Factor7 N/A 1.34
e - ISO Factor8 N/A 0.44
Y - ISO Factor9 N/A 1.38

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 407

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 78.5
Cg - Geometry Factor10 N/A 0.125
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.