Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 30232

Cone Part Number

 N/A X30232M

Cup Part Number

 N/A Y30232M

Design Unit

 N/A Metric

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A 30232M-90KA1 30232M-90KM1

Dimensions

d - Bore

 N/A 160 mm6.2992 in

D - Cup Outer Diameter

 N/A 290 mm11.4173 in

B - Cone Width

 N/A 48 mm1.8898 in

C - Cup Width

 N/A 40 mm1.5748 in

T - Bearing Width

 N/A 52 mm2.0472 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 4 mm0.16 in
r - Cup Backface "To Clear" Radius2 N/A 3 mm0.12 in

da - Cone Frontface Backing Diameter

 N/A 178 mm7.01 in

db - Cone Backface Backing Diameter

 N/A 185 mm7.28 in

Da - Cup Frontface Backing Diameter

 N/A 269 mm10.59 in

Db - Cup Backface Backing Diameter

 N/A 266 mm10.47 in

Ab - Cage-Cone Frontface Clearance

 N/A 6.1 mm0.24 in

Aa - Cage-Cone Backface Clearance

 N/A 5.3 mm0.21 in
a - Effective Center Location3 N/A 5.1 mm0.2 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 170000 N38300 lbf
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 657000 N148000 lbf

C0 - Static Radial Rating

 N/A 868000 N195000 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 127000 N28500 lbf

Factors

K - Factor7 N/A 1.34
e - ISO Factor8 N/A 0.44
Y - ISO Factor9 N/A 1.38

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 543

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 78
Cg - Geometry Factor10 N/A 0.116
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.