Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 30319

Cone Part Number

 N/A X30319M

Cup Part Number

 N/A Y30319M

Design Unit

 N/A Metric

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A 30319-90KA1 30319-9X241

Dimensions

d - Bore

 N/A 95 mm3.7402 in

D - Cup Outer Diameter

 N/A 200 mm7.874 in

B - Cone Width

 N/A 45 mm1.7717 in

C - Cup Width

 N/A 38 mm1.4961 in

T - Bearing Width

 N/A 49.5 mm1.9488 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 4 mm0.16 in
r - Cup Backface "To Clear" Radius2 N/A 3 mm0.12 in

da - Cone Frontface Backing Diameter

 N/A 111 mm4.37 in

db - Cone Backface Backing Diameter

 N/A 118 mm4.65 in

Da - Cup Frontface Backing Diameter

 N/A 184 mm7.24 in

Db - Cup Backface Backing Diameter

 N/A 182 mm7.17 in

Ab - Cage-Cone Frontface Clearance

 N/A 6.1 mm0.24 in

Aa - Cage-Cone Backface Clearance

 N/A 3.8 mm0.15 in
a - Effective Center Location3 N/A -9.4 mm-0.37 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 105000 N23500 lbf
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 404000 N90800 lbf

C0 - Static Radial Rating

 N/A 492000 N111000 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 61900 N13900 lbf

Factors

K - Factor7 N/A 1.69
e - ISO Factor8 N/A 0.35
Y - ISO Factor9 N/A 1.74

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 203.6

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 34.7
Cg - Geometry Factor10 N/A 0.0925
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.