Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 32030XM

Cone Part Number

 N/A X32030XM

Cup Part Number

 N/A Y32030XM

Design Unit

 N/A Metric

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 150 mm5.9055 in

D - Cup Outer Diameter

 N/A 225 mm8.8583 in

B - Cone Width

 N/A 48 mm1.8898 in

C - Cup Width

 N/A 36 mm1.4173 in

T - Bearing Width

 N/A 48.000 mm1.8898 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 3.050 mm0.12 in
r - Cup Backface "To Clear" Radius2 N/A 2.54 mm0.1 in

da - Cone Frontface Backing Diameter

 N/A 163 mm6.42 in

db - Cone Backface Backing Diameter

 N/A 169 mm6.65 in

Da - Cup Frontface Backing Diameter

 N/A 217.90 mm8.58 in

Db - Cup Backface Backing Diameter

 N/A 205.99 mm8.11 in

Ab - Cage-Cone Frontface Clearance

 N/A 3.8 mm0.15 in

Aa - Cage-Cone Backface Clearance

 N/A 4.3 mm0.17 in
a - Effective Center Location3 N/A 1 mm0.04 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 115000 N25800 lbf
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 443000 N99500 lbf

C0 - Static Radial Rating

 N/A 730000 N164000 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 90100 N20300 lbf

Factors

K - Factor7 N/A 1.27
e - ISO Factor8 N/A 0.46
Y - ISO Factor9 N/A 1.31

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 437

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 114.5
Cg - Geometry Factor10 N/A 0.131
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.