Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 32048X

Cone Part Number

 N/A X32048X

Cup Part Number

 N/A Y32048X

Design Unit

 N/A Metric

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A 32048X-90KA5

Dimensions

d - Bore

 N/A 240 mm9.4488 in

D - Cup Outer Diameter

 N/A 360 mm14.1732 in

B - Cone Width

 N/A 76 mm2.9921 in

C - Cup Width

 N/A 57 mm2.2441 in

T - Bearing Width

 N/A 76.000 mm2.9921 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 4.060 mm0.16 in
r - Cup Backface "To Clear" Radius2 N/A 3.05 mm0.12 in

da - Cone Frontface Backing Diameter

 N/A 259 mm10.2 in

db - Cone Backface Backing Diameter

 N/A 268 mm10.55 in

Da - Cup Frontface Backing Diameter

 N/A 346.96 mm13.66 in

Db - Cup Backface Backing Diameter

 N/A 330.96 mm13.03 in

Ab - Cage-Cone Frontface Clearance

 N/A 5.6 mm0.22 in

Aa - Cage-Cone Backface Clearance

 N/A 9.4 mm0.37 in
a - Effective Center Location3 N/A 2.2 mm0.09 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 306000 N68900 lbf
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 1180000 N266000 lbf

C0 - Static Radial Rating

 N/A 1940000 N435000 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 241000 N54100 lbf

Factors

K - Factor7 N/A 1.27
e - ISO Factor8 N/A 0.46
Y - ISO Factor9 N/A 1.31

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 1385

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 145
Cg - Geometry Factor10 N/A 0.161
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.