Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 32064XM

Cone Part Number

 N/A X32064XM

Cup Part Number

 N/A Y32064XM

Design Unit

 N/A Metric

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A 32064XM-90KM1

Dimensions

d - Bore

 N/A 320.000 mm12.5984 in

D - Cup Outer Diameter

 N/A 480 mm18.8976 in

B - Cone Width

 N/A 100 mm3.937 in

C - Cup Width

 N/A 74 mm2.9134 in

T - Bearing Width

 N/A 100.000 mm3.9370 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 5.080 mm0.200 in
r - Cup Backface "To Clear" Radius2 N/A 4.06 mm0.16 in

da - Cone Frontface Backing Diameter

 N/A 343 mm13.5 in

db - Cone Backface Backing Diameter

 N/A 357 mm14.06 in

Da - Cup Frontface Backing Diameter

 N/A 461.30 mm18.16 in

Db - Cup Backface Backing Diameter

 N/A 441.96 mm17.40 in

Ab - Cage-Cone Frontface Clearance

 N/A 6.9 mm0.27 in

Aa - Cage-Cone Backface Clearance

 N/A 11.9 mm0.47 in
a - Effective Center Location3 N/A 4.3 mm0.17 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 468000 N105000 lbf
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 1800000 N406000 lbf

C0 - Static Radial Rating

 N/A 3420000 N768000 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 367000 N82600 lbf

Factors

K - Factor7 N/A 1.27
e - ISO Factor8 N/A 0.46
Y - ISO Factor9 N/A 1.31

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 2667.3

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 201.4
Cg - Geometry Factor10 N/A 0.2
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.