Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 32248

Cone Part Number

 N/A X32248

Cup Part Number

 N/A Y32248

Design Unit

 N/A Metric

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A 32248-90KA1

Dimensions

d - Bore

 N/A 240 mm9.4488 in

D - Cup Outer Diameter

 N/A 440 mm17.3228 in

B - Cone Width

 N/A 120 mm4.7244 in

C - Cup Width

 N/A 100 mm3.937 in

T - Bearing Width

 N/A 127 mm5.0000 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 5 mm0.200 in
r - Cup Backface "To Clear" Radius2 N/A 4 mm0.16 in

da - Cone Frontface Backing Diameter

 N/A 280 mm11.02 in

db - Cone Backface Backing Diameter

 N/A 293 mm11.54 in

Da - Cup Frontface Backing Diameter

 N/A 415 mm16.34 in

Db - Cup Backface Backing Diameter

 N/A 394 mm15.51 in

Ab - Cage-Cone Frontface Clearance

 N/A 8.6 mm0.34 in

Aa - Cage-Cone Backface Clearance

 N/A 10.9 mm0.43 in
a - Effective Center Location3 N/A -17.5 mm-0.69 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 566000 N127000 lbf
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 2180000 N491000 lbf

C0 - Static Radial Rating

 N/A 3680000 N828000 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 422000 N94800 lbf

Factors

K - Factor7 N/A 1.34
e - ISO Factor8 N/A 0.44
Y - ISO Factor9 N/A 1.38

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 2021.3

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 103
Cg - Geometry Factor10 N/A 0.18
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.