Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 33030

Cone Part Number

 N/A X33030M

Cup Part Number

 N/A Y33030M

Design Unit

 N/A Metric

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A 33030M-90KM1

Dimensions

d - Bore

 N/A 150 mm5.9055 in

D - Cup Outer Diameter

 N/A 225 mm8.8583 in

B - Cone Width

 N/A 59 mm2.3228 in

C - Cup Width

 N/A 46 mm1.811 in

T - Bearing Width

 N/A 59 mm2.3228 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 3 mm0.12 in
r - Cup Backface "To Clear" Radius2 N/A 2.5 mm0.1 in

da - Cone Frontface Backing Diameter

 N/A 161 mm6.34 in

db - Cone Backface Backing Diameter

 N/A 169 mm6.65 in

Da - Cup Frontface Backing Diameter

 N/A 218 mm8.58 in

Db - Cup Backface Backing Diameter

 N/A 207 mm8.15 in

Ab - Cage-Cone Frontface Clearance

 N/A 4.6 mm0.18 in

Aa - Cage-Cone Backface Clearance

 N/A 4.6 mm0.18 in
a - Effective Center Location3 N/A -10.9 mm-0.43 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 145000 N32700 lbf
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 561000 N126000 lbf

C0 - Static Radial Rating

 N/A 949000 N213000 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 90800 N20400 lbf

Factors

K - Factor7 N/A 1.6
e - ISO Factor8 N/A 0.36
Y - ISO Factor9 N/A 1.65

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 541.5

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 102.4
Cg - Geometry Factor10 N/A 0.132
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.