Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 33109

Cone Part Number

 N/A X33109

Cup Part Number

 N/A Y33109

Design Unit

 N/A Metric

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A 33109-90KA1 33109-90KA2 33109-90NA3

Dimensions

d - Bore

 N/A 45 mm1.7717 in

D - Cup Outer Diameter

 N/A 80 mm3.1496 in

B - Cone Width

 N/A 26.000 mm1.0236 in

C - Cup Width

 N/A 20.500 mm0.8071 in

T - Bearing Width

 N/A 26.000 mm1.0236 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 1.520 mm0.06 in
r - Cup Backface "To Clear" Radius2 N/A 1.52 mm0.06 in

da - Cone Frontface Backing Diameter

 N/A 52 mm2.05 in

db - Cone Backface Backing Diameter

 N/A 55 mm2.17 in

Da - Cup Frontface Backing Diameter

 N/A 76.96 mm3.03 in

Db - Cup Backface Backing Diameter

 N/A 71.12 mm2.8 in

Ab - Cage-Cone Frontface Clearance

 N/A 2.3 mm0.09 in

Aa - Cage-Cone Backface Clearance

 N/A 1.5 mm0.06 in
a - Effective Center Location3 N/A -6.6 mm-0.26 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 29200 N6570 lbf
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 113000 N25300 lbf

C0 - Static Radial Rating

 N/A 119000 N26800 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 19200 N4310 lbf

Factors

K - Factor7 N/A 1.52
e - ISO Factor8 N/A 0.38
Y - ISO Factor9 N/A 1.57

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 35.7

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 16.5
Cg - Geometry Factor10 N/A 0.0843
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.