Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 33122

Cone Part Number

 N/A X33122M

Cup Part Number

 N/A Y33122M

Design Unit

 N/A Metric

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A 33122-90KA5 33122-9X241

Dimensions

d - Bore

 N/A 110 mm4.3307 in

D - Cup Outer Diameter

 N/A 180 mm7.0866 in

B - Cone Width

 N/A 56 mm2.2047 in

C - Cup Width

 N/A 43 mm1.6929 in

T - Bearing Width

 N/A 56 mm2.2047 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 2.5 mm0.1 in
r - Cup Backface "To Clear" Radius2 N/A 2 mm0.08 in

da - Cone Frontface Backing Diameter

 N/A 121 mm4.76 in

db - Cone Backface Backing Diameter

 N/A 130 mm5.12 in

Da - Cup Frontface Backing Diameter

 N/A 173.5 mm6.83 in

Db - Cup Backface Backing Diameter

 N/A 162 mm6.38 in

Ab - Cage-Cone Frontface Clearance

 N/A 3.3 mm0.13 in

Aa - Cage-Cone Backface Clearance

 N/A 6.1 mm0.24 in
a - Effective Center Location3 N/A -11.9 mm-0.47 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 107000 N24000 lbf
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 412000 N92700 lbf

C0 - Static Radial Rating

 N/A 635000 N143000 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 76600 N17200 lbf

Factors

K - Factor7 N/A 1.4
e - ISO Factor8 N/A 0.42
Y - ISO Factor9 N/A 1.43

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 285

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 57.3
Cg - Geometry Factor10 N/A 0.111
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.