Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 33217

Cone Part Number

 N/A X33217

Cup Part Number

 N/A Y33217

Design Unit

 N/A Metric

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A 33217-90KA1

Dimensions

d - Bore

 N/A 85 mm3.3465 in

D - Cup Outer Diameter

 N/A 150 mm5.9055 in

B - Cone Width

 N/A 49.000 mm1.9291 in

C - Cup Width

 N/A 37.000 mm1.4567 in

T - Bearing Width

 N/A 49.000 mm1.9291 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 2.540 mm0.1 in
r - Cup Backface "To Clear" Radius2 N/A 2.03 mm0.08 in

da - Cone Frontface Backing Diameter

 N/A 94 mm3.7 in

db - Cone Backface Backing Diameter

 N/A 103 mm4.06 in

Da - Cup Frontface Backing Diameter

 N/A 145.03 mm5.71 in

Db - Cup Backface Backing Diameter

 N/A 134.11 mm5.28 in

Ab - Cage-Cone Frontface Clearance

 N/A 4.1 mm0.16 in

Aa - Cage-Cone Backface Clearance

 N/A 4.8 mm0.19 in
a - Effective Center Location3 N/A -11.7 mm-0.46 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 108000 N24300 lbf
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 416000 N93600 lbf

C0 - Static Radial Rating

 N/A 483000 N109000 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 77300 N17400 lbf

Factors

K - Factor7 N/A 1.4
e - ISO Factor8 N/A 0.42
Y - ISO Factor9 N/A 1.43

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 167.6

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 33.3
Cg - Geometry Factor10 N/A 0.0995
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.