Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 33220

Cone Part Number

 N/A X33220M

Cup Part Number

 N/A Y33220M

Design Unit

 N/A Metric

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A 33220-90KA2 33220-9X241

Dimensions

d - Bore

 N/A 100 mm3.937 in

D - Cup Outer Diameter

 N/A 180 mm7.0866 in

B - Cone Width

 N/A 63 mm2.4803 in

C - Cup Width

 N/A 48 mm1.8898 in

T - Bearing Width

 N/A 63 mm2.4803 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 3 mm0.12 in
r - Cup Backface "To Clear" Radius2 N/A 2.5 mm0.1 in

da - Cone Frontface Backing Diameter

 N/A 112 mm4.41 in

db - Cone Backface Backing Diameter

 N/A 122 mm4.8 in

Da - Cup Frontface Backing Diameter

 N/A 172 mm6.77 in

Db - Cup Backface Backing Diameter

 N/A 160 mm6.3 in

Ab - Cage-Cone Frontface Clearance

 N/A 4.3 mm0.17 in

Aa - Cage-Cone Backface Clearance

 N/A 6.9 mm0.27 in
a - Effective Center Location3 N/A -17.3 mm-0.68 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 127000 N28500 lbf
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 488000 N110000 lbf

C0 - Static Radial Rating

 N/A 679000 N153000 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 87600 N19700 lbf

Factors

K - Factor7 N/A 1.44
e - ISO Factor8 N/A 0.4
Y - ISO Factor9 N/A 1.48

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 256.3

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 44
Cg - Geometry Factor10 N/A 0.106
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.