Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A HH221400

Cone Part Number

 N/A JHH221436

Cup Part Number

 N/A JHH221414P

Design Unit

 N/A Metric

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 90 mm3.5433 in

D - Cup Outer Diameter

 N/A 190 mm7.4803 in

B - Cone Width

 N/A 57.531 mm2.2650 in

C - Cup Width

 N/A 48.500 mm1.9094 in

T - Bearing Width

 N/A 59.500 mm2.3425 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 7.870 mm0.310 in
r - Cup Backface "To Clear" Radius2 N/A 3.05 mm0.12 in

da - Cone Frontface Backing Diameter

 N/A 106 mm4.17 in

db - Cone Backface Backing Diameter

 N/A 121 mm4.76 in

Da - Cup Frontface Backing Diameter

 N/A 179.10 mm7.06 in

Db - Cup Backface Backing Diameter

 N/A 170.94 mm6.73 in

Ab - Cage-Cone Frontface Clearance

 N/A 3.8 mm0.15 in

Aa - Cage-Cone Backface Clearance

 N/A 2 mm0.08 in
a - Effective Center Location3 N/A -15 mm-0.59 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 138000 N31100 lbf
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 534000 N120000 lbf

C0 - Static Radial Rating

 N/A 692000 N156000 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 79300 N17800 lbf

Factors

K - Factor7 N/A 1.74
e - ISO Factor8 N/A 0.33
Y - ISO Factor9 N/A 1.79

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 265.6

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 28.4
Cg - Geometry Factor10 N/A 0.107
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.