Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A HH224300

Cone Part Number

 N/A JHH224333

Cup Part Number

 N/A JHH224315

Design Unit

 N/A Metric

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 100 mm3.937 in

D - Cup Outer Diameter

 N/A 215 mm8.4646 in

B - Cone Width

 N/A 66.675 mm2.6250 in

C - Cup Width

 N/A 53.975 mm2.1250 in

T - Bearing Width

 N/A 66.675 mm2.6250 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 7.110 mm0.280 in
r - Cup Backface "To Clear" Radius2 N/A 3.30 mm0.130 in

da - Cone Frontface Backing Diameter

 N/A 120 mm4.72 in

db - Cone Backface Backing Diameter

 N/A 131 mm5.16 in

Da - Cup Frontface Backing Diameter

 N/A 201.70 mm7.95 in

Db - Cup Backface Backing Diameter

 N/A 193.04 mm7.60 in

Ab - Cage-Cone Frontface Clearance

 N/A 3.6 mm0.14 in

Aa - Cage-Cone Backface Clearance

 N/A 4.1 mm0.16 in
a - Effective Center Location3 N/A -18.9 mm-0.74 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 176000 N39600 lbf
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 680000 N153000 lbf

C0 - Static Radial Rating

 N/A 906000 N204000 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 98300 N22100 lbf

Factors

K - Factor7 N/A 1.79
e - ISO Factor8 N/A 0.33
Y - ISO Factor9 N/A 1.84

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 367

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 47.8
Cg - Geometry Factor10 N/A 0.118
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.