Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A HM534100

Cone Part Number

 N/A JHM534149

Cup Part Number

 N/A JHM534110

Design Unit

 N/A Metric

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A JHM534149-90B01

Dimensions

d - Bore

 N/A 170 mm6.6929 in

D - Cup Outer Diameter

 N/A 230 mm9.0551 in

B - Cone Width

 N/A 38.000 mm1.4961 in

C - Cup Width

 N/A 31.000 mm1.2205 in

T - Bearing Width

 N/A 39.000 mm1.5354 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 3.050 mm0.12 in
r - Cup Backface "To Clear" Radius2 N/A 2.54 mm0.1 in

da - Cone Frontface Backing Diameter

 N/A 178 mm7.01 in

db - Cone Backface Backing Diameter

 N/A 184 mm7.24 in

Da - Cup Frontface Backing Diameter

 N/A 224.54 mm8.84 in

Db - Cup Backface Backing Diameter

 N/A 216.92 mm8.54 in

Ab - Cage-Cone Frontface Clearance

 N/A 4.1 mm0.16 in

Aa - Cage-Cone Backface Clearance

 N/A 0.5 mm0.02 in
a - Effective Center Location3 N/A 4.6 mm0.18 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 86800 N19500 lbf
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 335000 N75300 lbf

C0 - Static Radial Rating

 N/A 590000 N133000 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 56900 N12800 lbf

Factors

K - Factor7 N/A 1.52
e - ISO Factor8 N/A 0.38
Y - ISO Factor9 N/A 1.57

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 480

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 89.8
Cg - Geometry Factor10 N/A 0.135
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.