Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A HM840400

Cone Part Number

 N/A JHM840449

Cup Part Number

 N/A JHM840410

Design Unit

 N/A Metric

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A JHM840449-90B01 JHM840449-90BA3 JHM840449-90CA4

Dimensions

d - Bore

 N/A 200 mm7.874 in

D - Cup Outer Diameter

 N/A 300 mm11.811 in

B - Cone Width

 N/A 62 mm2.4409 in

C - Cup Width

 N/A 51.000 mm2.0079 in

T - Bearing Width

 N/A 65.000 mm2.5591 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 3.560 mm0.14 in
r - Cup Backface "To Clear" Radius2 N/A 2.54 mm0.1 in

da - Cone Frontface Backing Diameter

 N/A 215 mm8.46 in

db - Cone Backface Backing Diameter

 N/A 226 mm8.9 in

Da - Cup Frontface Backing Diameter

 N/A 290.07 mm11.42 in

Db - Cup Backface Backing Diameter

 N/A 273.05 mm10.75 in

Ab - Cage-Cone Frontface Clearance

 N/A 7.1 mm0.28 in

Aa - Cage-Cone Backface Clearance

 N/A 3.8 mm0.15 in
a - Effective Center Location3 N/A 8.1 mm0.32 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 180000 N40500 lbf
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 695000 N156000 lbf

C0 - Static Radial Rating

 N/A 1280000 N287000 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 161000 N36200 lbf

Factors

K - Factor7 N/A 1.12
e - ISO Factor8 N/A 0.52
Y - ISO Factor9 N/A 1.15

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 854

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 126
Cg - Geometry Factor10 N/A 0.143
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.