Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A L286900

Cone Part Number

 N/A JL286949H

Cup Part Number

 N/A JL286910

Design Unit

 N/A Metric

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A JL286949H-90KA3

Dimensions

d - Bore

 N/A 930.000 mm36.6142 in

D - Cup Outer Diameter

 N/A 1060.000 mm41.7323 in

B - Cone Width

 N/A 90.000 mm3.5433 in

C - Cup Width

 N/A 76.000 mm2.9921 in

T - Bearing Width

 N/A 92.000 mm3.6220 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 3.300 mm0.13 in
r - Cup Backface "To Clear" Radius2 N/A 3.30 mm0.130 in

da - Cone Frontface Backing Diameter

 N/A 951 mm37.44 in

db - Cone Backface Backing Diameter

 N/A 954 mm37.56 in

Da - Cup Frontface Backing Diameter

 N/A 1047.24 mm41.23 in

Db - Cup Backface Backing Diameter

 N/A 1029.97 mm40.55 in

Ab - Cage-Cone Frontface Clearance

 N/A 11.4 mm0.45 in

Aa - Cage-Cone Backface Clearance

 N/A 1 mm0.04 in
a - Effective Center Location3 N/A 59.9 mm2.36 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 691000 N155000 lbf
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 2660000 N599000 lbf

C0 - Static Radial Rating

 N/A 8460000 N1900000 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 393000 N88400 lbf

Factors

K - Factor7 N/A 1.76
e - ISO Factor8 N/A 0.33
Y - ISO Factor9 N/A 1.8

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 27827.6

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 4055.4
Cg - Geometry Factor10 N/A 0.381
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.