Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A M719100

Cone Part Number

 N/A JM719149

Cup Part Number

 N/A JM719113

Design Unit

 N/A Metric

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A JM719149-90B01 JM719149-90C01

Dimensions

d - Bore

 N/A 95 mm3.7402 in

D - Cup Outer Diameter

 N/A 150 mm5.9055 in

B - Cone Width

 N/A 34.000 mm1.3386 in

C - Cup Width

 N/A 27 mm1.063 in

T - Bearing Width

 N/A 35.000 mm1.3780 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 3.050 mm0.12 in
r - Cup Backface "To Clear" Radius2 N/A 2.54 mm0.1 in

da - Cone Frontface Backing Diameter

 N/A 104 mm4.09 in

db - Cone Backface Backing Diameter

 N/A 109 mm4.29 in

Da - Cup Frontface Backing Diameter

 N/A 143.26 mm5.64 in

Db - Cup Backface Backing Diameter

 N/A 134.87 mm5.31 in

Ab - Cage-Cone Frontface Clearance

 N/A 3.6 mm0.14 in

Aa - Cage-Cone Backface Clearance

 N/A 2.8 mm0.11 in
a - Effective Center Location3 N/A -1.6 mm-0.06 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 55700 N12500 lbf
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 215000 N48300 lbf

C0 - Static Radial Rating

 N/A 316000 N71100 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 42100 N9470 lbf

Factors

K - Factor7 N/A 1.32
e - ISO Factor8 N/A 0.44
Y - ISO Factor9 N/A 1.36

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 150

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 36.1
Cg - Geometry Factor10 N/A 0.141
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.