Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A M736100

Cone Part Number

 N/A JM736149

Cup Part Number

 N/A JM736110

Design Unit

 N/A Metric

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A JM736149-90B01

Dimensions

d - Bore

 N/A 180 mm7.0866 in

D - Cup Outer Diameter

 N/A 250 mm9.8425 in

B - Cone Width

 N/A 45 mm1.7717 in

C - Cup Width

 N/A 37.000 mm1.4567 in

T - Bearing Width

 N/A 47.000 mm1.8504 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 3.050 mm0.12 in
r - Cup Backface "To Clear" Radius2 N/A 2.54 mm0.1 in

da - Cone Frontface Backing Diameter

 N/A 190.5 mm7.5 in

db - Cone Backface Backing Diameter

 N/A 196 mm7.72 in

Da - Cup Frontface Backing Diameter

 N/A 243.08 mm9.57 in

Db - Cup Backface Backing Diameter

 N/A 231.90 mm9.13 in

Ab - Cage-Cone Frontface Clearance

 N/A 4.8 mm0.19 in

Aa - Cage-Cone Backface Clearance

 N/A 2.8 mm0.11 in
a - Effective Center Location3 N/A 8.9 mm0.35 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 106000 N23800 lbf
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 409000 N92000 lbf

C0 - Static Radial Rating

 N/A 786000 N177000 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 87200 N19600 lbf

Factors

K - Factor7 N/A 1.22
e - ISO Factor8 N/A 0.48
Y - ISO Factor9 N/A 1.25

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 589.4

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 128
Cg - Geometry Factor10 N/A 0.123
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.