Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A JP18000

Cone Part Number

 N/A JP18049

Cup Part Number

 N/A JP18010

Design Unit

 N/A Metric

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A JP18049-90BA1 JP18049-90KA2

Dimensions

d - Bore

 N/A 180 mm7.0866 in

D - Cup Outer Diameter

 N/A 240 mm9.4488 in

B - Cone Width

 N/A 30.000 mm1.1811 in

C - Cup Width

 N/A 23.000 mm0.9055 in

T - Bearing Width

 N/A 32.000 mm1.2598 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 3.050 mm0.12 in
r - Cup Backface "To Clear" Radius2 N/A 3.05 mm0.12 in

da - Cone Frontface Backing Diameter

 N/A 189 mm7.44 in

db - Cone Backface Backing Diameter

 N/A 194 mm7.64 in

Da - Cup Frontface Backing Diameter

 N/A 233.68 mm9.20 in

Db - Cup Backface Backing Diameter

 N/A 227.08 mm8.94 in

Ab - Cage-Cone Frontface Clearance

 N/A 4.8 mm0.19 in

Aa - Cage-Cone Backface Clearance

 N/A 2.8 mm0.11 in
a - Effective Center Location3 N/A 16 mm0.63 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 61800 N13900 lbf
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 239000 N53600 lbf

C0 - Static Radial Rating

 N/A 409000 N92000 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 51300 N11500 lbf

Factors

K - Factor7 N/A 1.21
e - ISO Factor8 N/A 0.48
Y - ISO Factor9 N/A 1.24

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 369.2

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 161.8
Cg - Geometry Factor10 N/A 0.104
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.