Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 30240

Cone Part Number

 N/A X30240

Cup Part Number

 N/A Y30240

Design Unit

 N/A Metric

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A 30240-90KA1 30240-90KA4

Dimensions

d - Bore

 N/A 200 mm7.874 in

D - Cup Outer Diameter

 N/A 360 mm14.1732 in

B - Cone Width

 N/A 58.000 mm2.2835 in

C - Cup Width

 N/A 48 mm1.8898 in

T - Bearing Width

 N/A 64.000 mm2.5197 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 5.080 mm0.200 in
r - Cup Backface "To Clear" Radius2 N/A 0.00 mm0.000 in

da - Cone Frontface Backing Diameter

 N/A 227 mm8.94 in

db - Cone Backface Backing Diameter

 N/A 231 mm9.09 in

Da - Cup Frontface Backing Diameter

 N/A 337.06 mm13.27 in

Db - Cup Backface Backing Diameter

 N/A 331.00 mm13.03 in

Ab - Cage-Cone Frontface Clearance

 N/A 9.7 mm0.38 in

Aa - Cage-Cone Backface Clearance

 N/A 4.6 mm0.18 in
a - Effective Center Location3 N/A 7.9 mm0.31 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 231000 N51900 lbf
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 891000 N200000 lbf

C0 - Static Radial Rating

 N/A 1330000 N299000 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 172000 N38700 lbf

Factors

K - Factor7 N/A 1.34
e - ISO Factor8 N/A 0.44
Y - ISO Factor9 N/A 1.38

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 876.8

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 106.9
Cg - Geometry Factor10 N/A 0.135
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.