Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 32240

Cone Part Number

 N/A X32240

Cup Part Number

 N/A Y32240

Design Unit

 N/A Metric

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A 32240-90KA1 32240-90KA2 32240-90KA7

Dimensions

d - Bore

 N/A 200 mm7.874 in

D - Cup Outer Diameter

 N/A 360 mm14.1732 in

B - Cone Width

 N/A 98 mm3.8583 in

C - Cup Width

 N/A 82 mm3.2283 in

T - Bearing Width

 N/A 104.000 mm4.0945 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 5 mm0.197 in
r - Cup Backface "To Clear" Radius2 N/A 4 mm0.16 in

da - Cone Frontface Backing Diameter

 N/A 229 mm9.21 in

db - Cone Backface Backing Diameter

 N/A 240 mm9.45 in

Da - Cup Frontface Backing Diameter

 N/A 340 mm13.39 in

Db - Cup Backface Backing Diameter

 N/A 326 mm12.83 in

Ab - Cage-Cone Frontface Clearance

 N/A 7.4 mm0.29 in

Aa - Cage-Cone Backface Clearance

 N/A 15.5 mm0.61 in
a - Effective Center Location3 N/A -20.3 mm-0.8 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 360000 N80900 lbf
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 1390000 N312000 lbf

C0 - Static Radial Rating

 N/A 2250000 N506000 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 250000 N56300 lbf

Factors

K - Factor7 N/A 1.44
e - ISO Factor8 N/A 0.41
Y - ISO Factor9 N/A 1.48

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 1227.1

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 110.8
Cg - Geometry Factor10 N/A 0.149
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.