Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 32244

Cone Part Number

 N/A X32244M

Cup Part Number

 N/A Y32244M

Design Unit

 N/A Metric

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 220 mm8.6614 in

D - Cup Outer Diameter

 N/A 400 mm15.748 in

B - Cone Width

 N/A 108 mm4.252 in

C - Cup Width

 N/A 90 mm3.5433 in

T - Bearing Width

 N/A 114.000 mm4.4882 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 5 mm0.200 in
r - Cup Backface "To Clear" Radius2 N/A 4 mm0.16 in

da - Cone Frontface Backing Diameter

 N/A 251 mm9.88 in

db - Cone Backface Backing Diameter

 N/A 268 mm10.55 in

Da - Cup Frontface Backing Diameter

 N/A 379.5 mm14.94 in

Db - Cup Backface Backing Diameter

 N/A 362 mm14.25 in

Ab - Cage-Cone Frontface Clearance

 N/A 8.4 mm0.33 in

Aa - Cage-Cone Backface Clearance

 N/A 9.9 mm0.39 in
a - Effective Center Location3 N/A -15 mm-0.59 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 549000 N123000 lbf
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 2120000 N476000 lbf

C0 - Static Radial Rating

 N/A 3010000 N677000 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 409000 N92000 lbf

Factors

K - Factor7 N/A 1.34
e - ISO Factor8 N/A 0.44
Y - ISO Factor9 N/A 1.38

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 1607.6

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 113.5
Cg - Geometry Factor10 N/A 0.1669
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.