Batch CAD Cart (0)
  • Cart is empty
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

N/A 32952

Cone Part Number

N/A X32952M

Cup Part Number

N/A Y32952M

Design Unit

N/A Metric

Cage Material

N/A Stamped Steel

Dimensions

d - Bore

N/A 260 mm10.2362 in

D - Cup Outer Diameter

N/A 360 mm14.1732 in

B - Cone Width

N/A 63.5 mm2.5 in

C - Cup Width

N/A 48 mm1.8898 in

T - Bearing Width

N/A 63.500 mm2.5000 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 3 mm0.12 in
r - Cup Backface "To Clear" Radius2 N/A 2.5 mm0.1 in

da - Cone Frontface Backing Diameter

N/A 275 mm10.83 in

db - Cone Backface Backing Diameter

N/A 280 mm11.02 in

Da - Cup Frontface Backing Diameter

N/A 347.5 mm13.68 in

Db - Cup Backface Backing Diameter

N/A 337 mm13.27 in

Ab - Cage-Cone Frontface Clearance

N/A 4.6 mm0.18 in

Aa - Cage-Cone Backface Clearance

N/A 6.1 mm0.24 in
a - Effective Center Location3 N/A 6.1 mm0.24 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 215000 N48300 lbf
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 829000 N186000 lbf

C0 - Static Radial Rating

N/A 1690000 N379000 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 150000 N33600 lbf

Factors

K - Factor7 N/A 1.44
e - ISO Factor8 N/A 0.41
Y - ISO Factor9 N/A 1.48

G1 - Heat Generation Factor (Roller-Raceway)

N/A 1503.1

G2 - Heat Generation Factor (Rib-Roller End)

N/A 206.8
Cg - Geometry Factor10 N/A 0.158
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.
By clicking Submit, you consent to the personal information you provide being used in the manner as described in our Privacy Notice, including access to that information by Timken personnel who may be located outside your home country. In addition, you agree that the CAD drawings are for your personal, one-time use only, and that you will not modify or create any compilation or derivative work using the CAD drawings or distribute or display the CAD drawings on any website or other media.