Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

 N/A 33212

Cone Part Number

 N/A XAA33212

Cup Part Number

 N/A Y33212

Design Unit

 N/A Metric

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 60 mm2.3622 in

D - Cup Outer Diameter

 N/A 110 mm4.3307 in

B - Cone Width

 N/A 38.000 mm1.4961 in

C - Cup Width

 N/A 29.000 mm1.1417 in

T - Bearing Width

 N/A 38.000 mm1.4961 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 6.100 mm0.24 in
r - Cup Backface "To Clear" Radius2 N/A 1.52 mm0.06 in

da - Cone Frontface Backing Diameter

 N/A 68 mm2.68 in

db - Cone Backface Backing Diameter

 N/A 85 mm3.35 in

Da - Cup Frontface Backing Diameter

 N/A 105.40 mm4.15 in

Db - Cup Backface Backing Diameter

 N/A 98.04 mm3.86 in

Ab - Cage-Cone Frontface Clearance

 N/A 3.3 mm0.13 in

Aa - Cage-Cone Backface Clearance

 N/A 3.3 mm0.13 in
a - Effective Center Location3 N/A -9.9 mm-0.39 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 60700 N13700 lbf
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 234000 N52700 lbf

C0 - Static Radial Rating

 N/A 253000 N56800 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 42000 N9450 lbf

Factors

K - Factor7 N/A 1.44
e - ISO Factor8 N/A 0.4
Y - ISO Factor9 N/A 1.48

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 76.2

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 18.1
Cg - Geometry Factor10 N/A 0.0758
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.