Montage of Timken Bearing Products 
Search Catalog
        
 All Product Types    UFH Type with Keyway, Regular Version - Inch (Imperial) Bores
View Cart View RFQs Express Ordering  | Shipping 
 | Tax 
 | Terms
 Shopping Cart 0 Items
 Request for Quote 0 Items
All Product Types > INDUSTRIAL MOTION PRODUCTS > Couplings & Power Transmission Parts Catalog > Specialty Products - Deltaflex, Uniflex, Saga, Rigid Sleeve, Shaft Collars > Uniflex Couplings > UFH Type with Keyway, Regular Version - Inch (Imperial) Bores > Part Number 68514445397  
Download PDF Download PDF     Printable Page     Email Email This Page     Save To Favorites Save To Favorites
Add To Cart Request Quote

Part Number 68514445397, UFH Type with Keyway, Regular Version - Inch (Imperial) Bores


UFH Type - Flange-to-Shaft
    A flange-to-shaft configuration, this couples flange mounted equipment to a shaft with all the benefits of Uniflex versatility. The stock flange plate is the same as used on the UF Type.

    The one-piece UFH Type coupling is similar to the U Type, except that one hub is replaced by a flange plate. Stock flange sizes are shown in the Dimensional Data table below but other sizes can be made to order. As with the other Uniflex styles, this coupling compensates for high degrees of angular and parallel misalignment with very little backlash or windup and is reliable in harsh or severe environments.

    Regular and short versions are available for each size to accommodate different overall length requirements. For increased versatility, the hub can be modified with a tapered, spline, hex or square bore. The standard hub is furnished with either a pre-drilled pin hole or with a keyway and set screw. Specify when ordering.
    Note: The UFH Type coupling does not come with assembly hardware. Assembly hardware must be purchased separately.



Unit of Measure: Imperial Metric Both

Specifications  · Dimensional Data  · Performance Data  · Coupling Design  · Notes

Specifications

Description 
UFH137R-CP-1-1/8-1/4X1/8KW

Hub Style
Regular

Type
Flange-to-Shaft

Material
Steel

Weight
4.50 lb

Color
Gray/Metallic

Bore Type
Finished Bore

# of Mounting Screws Required
3


Dimensional Data

Bore Size 
1 1/8 in

Hub Size
URH137R

Set Screw Thread Size (Dimension T)
3/8-16

Keyway Size (W x D)
1/4 x 1/8 in

Dimension HD
2.54 in
64.52 mm

Overall Length
4.030 in
102.36 mm

Pin Location (Dimension SL)
0.69 in

Length thru Bore
1.580 in
40.13 mm

Min. Bore (Dimensions ID1/ID2)
0.625 in
15.88 mm

Max. Bore (Dimensions ID1/ID2)
1.375 in
35.00 mm

Dimension BC
3.750 in
95.25 mm

Dimension D
4.250 in
107.95 mm

Flange Diameter (Dimension FD)
4.380 in
111.25 mm

Dimension FL
0.500 in
12.70 mm

Mounting Screw Thread Size
3/8-16

Cubic inches
77.31313 in³


Performance Data

Operating Temperature Range
-40 to 250 ºF

Max. Torque
1260 in·lb

Max. Speed
6000 rpm

Max. Recommended End Play
0.040 in
1.02 mm

Max. Parallel Offset
0.035 in
0.89 mm

Wind-Up Angle at Nominal Torque
1.85 º

Wind-Up Angle at Max. Torque
3.00 º

Rated HP at 100 rpm
2.02 hp

# of Set Screws Required
1


Coupling Design
Flexible Spring Type Coupling with Exclusive Triple Wound Spring Design
    The Uniflex Coupling is an all steel, single piece coupling that solves a variety of application concerns including: high misalignment, space limitations, high temperature, and exceptionally low backlash/windup. The unique flexing center of the Uniflex consists of three opposingly wound square wire springs for forward or reverse operation. Two steel hubs are then brazed to the steel spring pack to create a durable one-piece flexible coupling.




Notes

Notes 
  • Total backlash is approximately 1/3 of windup at maximum torque – consult Lovejoy Engineering for more information.
  • OAL & Dimension FL Tolerance + .12 inch.
  • Mounting screws not supplied.


 DOWNLOADS 

Specialty Products Catalog
(PDF, 0KB)

Uniflex Installation Instructions
(PDF, 0KB)


Add To Cart Request Quote
<