CAD (0) ▾
  • Cart is empty
  1. Request CAD files

Key Features

  • Available in single, double and multi-row configurations, as well as proprietary sizes
  • Designed in collaboration with OE engineers to design, engineer and test bearings for premium performance in many applications
  • Power dense designs allow for heavier loads and can help extend bearing life
  • Optimized internal geometry lower torque and operating temperatures to extend lubrication system life
  • Can be designed to withstand high-corrosive, high-temperature and vacuum or low-lubrication environments with proprietary enhancements
Request Information
Unit of Measure

Key Dimensions

Cone Part Number

 N/A 95499D

Cup Part Number

 N/A 95926

Bore (d)

 N/A 5 in127 mm

O.D. (D)

 N/A 9.25 in234.95 mm

Width (T)

 N/A 5.4999 in139.697 mm
Dynamic Radial Load Rating - 1M Revs (C1) 1 N/A 246000 lbf1090000 N
Dynamic Radial Load Rating - 90M Revs (C90) 2 N/A 36700 lbf163000 N
Dynamic Radial Load Rating 2-Row - 90M Revs (C90-2row) 3 N/A 63800 lbf284000 N
e Factor4 N/A 0.37
K Factor5 N/A 1.58

Other Dimensions

Inner Ring Width (B)

 N/A 6 in152.4 mm
Max Shaft Fillet Radius6 N/A 0.2 in5.1 mm
Max Housing Fillet Radius7 N/A 0.13 in3.3 mm

Shaft Backing Shoulder Diameter - Frontface (da)

 N/A 5.98 in152 mm

Housing Backing Shoulder Diameter - Backface (Db)

 N/A 8.23 in209.04 mm

Cage Location Relative to Frontface (Ab) 

 N/A -0.06 in-1.5 mm

Outer Ring Width (C)

 N/A 1.9375 in49.213 mm

Series

 N/A 95000

Weight

 N/A 6.6 lb3.0 Kg

Ratings

Dynamic Axial Rating - 90M Revs (Ca90) 8 N/A 23200 lbf103000 N

Factors

Y1 Factor 9 N/A 1.83
Y2 Factor 10 N/A 2.72

G1 Factor 

 N/A 454

G2 Factor 

 N/A 59.3
Geometry Factor (Cg) 11 N/A 0.132

Spacer

Note

 N/A Spacer shows standard nominal .01 radii, actual bearing may vary
  • 1 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 2 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 3 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 4 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 5 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 6 These maximum fillet radii will be cleared by the bearing corners.
  • 7 These maximum fillet radii will be cleared by the bearing corners.
  • 8 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 11 Geometry constant for Lubrication Life Adjustment Factor a3l.