The Timken Company
The Timken Company
4500 Mt Pleasant St. NW
N. Canton, OH 44720
Phone: (234) 262-3000
E-Mail: CustomerCAD@timken.com • Web site: www.timken.com
Print Back

Key Features

  • Available in single, double and multi-row configurations, as well as proprietary sizes
  • Designed in collaboration with OE engineers to design, engineer and test bearings for premium performance in many applications
  • Power dense designs allow for heavier loads and can help extend bearing life
  • Optimized internal geometry lower torque and operating temperatures to extend lubrication system life
  • Can be designed to withstand high-corrosive, high-temperature and vacuum or low-lubrication environments with proprietary enhancements
Unit of Measure

Key Dimensions

Cone Part Number

 N/A 67985D

Cup Part Number

 N/A 67919

Bore (d)

 N/A 8.125 in206.375 mm

O.D. (D)

 N/A 11 in279.4 mm

Width (T)

 N/A 3.4375 in87.313 mm
Dynamic Radial Load Rating - 1M Revs (C1) 1 N/A 166000 lbf738000 N
Dynamic Radial Load Rating - 90M Revs (C90) 2 N/A 24700 lbf110000 N
Dynamic Radial Load Rating 2-Row - 90M Revs (C90-2row) 3 N/A 43000 lbf191000 N
e Factor4 N/A 0.51
K Factor5 N/A 1.15

Other Dimensions

Inner Ring Width (B)

 N/A 3.4375 in87.313 mm
Max Shaft Fillet Radius6 N/A 0.03 in0.8 mm
Max Housing Fillet Radius7 N/A 0.13 in3.3 mm

Shaft Backing Shoulder Diameter - Frontface (da)

 N/A 8.62 in219 mm

Housing Backing Shoulder Diameter - Backface (Db)

 N/A 10.20 in259.08 mm

Cage Location Relative to Frontface (Ab) 

 N/A 0.11 in2.8 mm

Outer Ring Width (C)

 N/A 1.4375 in36.513 mm

Series

 N/A 67900

Weight

 N/A 1.4 lb0.6 Kg

Ratings

Dynamic Axial Rating - 90M Revs (Ca90) 8 N/A 21500 lbf95800 N

Factors

Y1 Factor 9 N/A 1.33
Y2 Factor 10 N/A 1.97

G1 Factor 

 N/A 820

G2 Factor 

 N/A 172
Geometry Factor (Cg) 11 N/A 0.139

Spacer

Note

 N/A Spacer shows standard nominal .01 radii, actual bearing may vary
  • 1 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 2 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 3 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 4 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 5 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 6 These maximum fillet radii will be cleared by the bearing corners.
  • 7 These maximum fillet radii will be cleared by the bearing corners.
  • 8 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 11 Geometry constant for Lubrication Life Adjustment Factor a3l.