The Timken Company
The Timken Company
4500 Mt Pleasant St. NW
N. Canton, OH 44720
Phone: (234) 262-3000
E-Mail: CustomerCAD@timken.com • Web site: www.timken.com
Print Back

Key Features

  • Available in single, double and multi-row configurations, as well as proprietary sizes
  • Designed in collaboration with OE engineers to design, engineer and test bearings for premium performance in many applications
  • Power dense designs allow for heavier loads and can help extend bearing life
  • Optimized internal geometry lower torque and operating temperatures to extend lubrication system life
  • Can be designed to withstand high-corrosive, high-temperature and vacuum or low-lubrication environments with proprietary enhancements
Unit of Measure

Key Dimensions

Cone Part Number

 N/A LM263149D

Cup Part Number

 N/A LM263110

Bore (d)

 N/A 14 in355.6 mm

O.D. (D)

 N/A 18 in457.2 mm

Width (T)

 N/A 4.7499 in120.647 mm
Dynamic Radial Load Rating - 1M Revs (C1) 1 N/A 368000 lbf1640000 N
Dynamic Radial Load Rating - 90M Revs (C90) 2 N/A 54900 lbf244000 N
Dynamic Radial Load Rating 2-Row - 90M Revs (C90-2row) 3 N/A 95500 lbf425000 N
e Factor4 N/A 0.32
K Factor5 N/A 1.83

Other Dimensions

Inner Ring Width (B)

 N/A 4.75 in120.65 mm
Max Shaft Fillet Radius6 N/A 0.06 in1.5 mm
Max Housing Fillet Radius7 N/A 0.13 in3.3 mm

Shaft Backing Shoulder Diameter - Frontface (da)

 N/A 14.65 in372 mm

Housing Backing Shoulder Diameter - Backface (Db)

 N/A 17.09 in434.1 mm

Cage Location Relative to Frontface (Ab) 

 N/A 0.19 in4.8 mm

Outer Ring Width (C)

 N/A 2 in50.8 mm

Series

 N/A LM263100

Weight

 N/A 3.1 lb1.4 Kg

Ratings

Dynamic Axial Rating - 90M Revs (Ca90) 8 N/A 29900 lbf133000 N

Factors

Y1 Factor 9 N/A 2.12
Y2 Factor 10 N/A 3.15

G1 Factor 

 N/A 3090

G2 Factor 

 N/A 470
Geometry Factor (Cg) 11 N/A 0.185

Spacer

Note

 N/A Spacer shows standard nominal .01 radii, actual bearing may vary
  • 1 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 2 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 3 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 4 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 5 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 6 These maximum fillet radii will be cleared by the bearing corners.
  • 7 These maximum fillet radii will be cleared by the bearing corners.
  • 8 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 11 Geometry constant for Lubrication Life Adjustment Factor a3l.