The Timken Company
The Timken Company
4500 Mt Pleasant St. NW
N. Canton, OH 44720
Phone: (234) 262-3000
E-Mail: CustomerCAD@timken.com • Web site: www.timken.com
Print Back

Key Features

  • Available in single, double and multi-row configurations, as well as proprietary sizes
  • Designed in collaboration with OE engineers to design, engineer and test bearings for premium performance in many applications
  • Power dense designs allow for heavier loads and can help extend bearing life
  • Optimized internal geometry lowers torque and operating temperatures to extend lubrication system life
  • Can be designed to withstand high-corrosive, high-temperature and vacuum or low-lubrication environments with proprietary enhancements
Unit of Measure

Key Dimensions

Cone Part Number

 N/A X32320M

Cup Part Number

 N/A Y32320M

Bore (d)

 N/A 100 mm3.937 in

O.D. (D)

 N/A 215 mm8.4646 in

Width (T)

 N/A 77.500 mm3.0512 in
Dynamic Radial Load Rating - 1M Revs (C1) 1 N/A 621000 N140000 lbf
Dynamic Radial Load Rating - 90M Revs (C90) 2 N/A 161000 N36200 lbf
e Factor 3 N/A 0.35
K Factor 4 N/A 1.69

Series

 N/A 32320M
Y Factor 5 N/A 1.74

Other Dimensions

Inner Ring Width (B)

 N/A 73.000 mm2.8740 in

Outer Ring Width (C)

 N/A 60.000 mm2.3622 in
Effective Center Location6 N/A -26.9 mm-1.06 in
Max Shaft Fillet Radius7 N/A 4.060 mm0.16 in
Max Housing Fillet Radius8 N/A 3.05 mm0.12 in

Shaft Backing Shoulder Diameter - Frontface (da)

 N/A 124 mm4.88 in

Shaft Backing Shoulder Diameter - Backface (db)

 N/A 129 mm5.08 in

Housing Backing Shoulder Diameter - Frontface (Da)

 N/A 200.91 mm7.91 in

Housing Backing Shoulder Diameter - Backface (Db)

 N/A 193.04 mm7.60 in

Cage Location Relative to Backface (Aa)

 N/A 13 mm0.51 in

Cage Location Relative to Frontface (Ab) 

 N/A 6.1 mm0.24 in

Weight

 N/A 12.9 Kg28.5 lb

Ratings

Dynamic Axial Rating - 90M Revs (Ca90)9 N/A 95100 N21400 lbf

Static Radial Load Rating (C0)

 N/A 883000 N198000 lbf

Factors

G1 Factor

 N/A 376.3

G2 Factor

 N/A 54.8
Geometry Factor (Cg)10 N/A 0.115
  • 1 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 2 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 3 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 4 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 5 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 6 Negative value indicates effective center inside cone backface.
  • 7 These maximum fillet radii will be cleared by the bearing corners.
  • 8 These maximum fillet radii will be cleared by the bearing corners.
  • 9 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.