The Timken Company
The Timken Company
4500 Mt Pleasant St. NW
N. Canton, OH 44720
Phone: (234) 262-3000
E-Mail: CustomerCAD@timken.com • Web site: www.timken.com
Print Back

Key Features

  • Available in single, double and multi-row configurations, as well as proprietary sizes
  • Designed in collaboration with OE engineers to design, engineer and test bearings for premium performance in many applications
  • Power dense designs allow for heavier loads and can help extend bearing life
  • Optimized internal geometry lowers torque and operating temperatures to extend lubrication system life
  • Can be designed to withstand high-corrosive, high-temperature and vacuum or low-lubrication environments with proprietary enhancements
Unit of Measure

Key Dimensions

Cone Part Number

 N/A XFA30206CM

Cup Part Number

 N/A Y30206CM

Bore (d)

 N/A 27.000 mm1.0630 in

O.D. (D)

 N/A 62 mm2.4409 in

Width (T)

 N/A 17.25 mm0.6791 in
Dynamic Radial Load Rating - 1M Revs (C1) 1 N/A 49300 N11100 lbf
Dynamic Radial Load Rating - 90M Revs (C90) 2 N/A 12800 N2880 lbf
e Factor 3 N/A 0.37
K Factor 4 N/A 1.56

Series

 N/A 30206C
Y Factor 5 N/A 1.6

Other Dimensions

Inner Ring Width (B)

 N/A 16 mm0.6299 in

Outer Ring Width (C)

 N/A 14 mm0.5512 in
Effective Center Location6 N/A -3.6 mm-0.14 in
Max Shaft Fillet Radius7 N/A 1.02 mm0.04 in
Max Housing Fillet Radius8 N/A 1.02 mm0.04 in

Shaft Backing Shoulder Diameter - Frontface (da)

 N/A 34.5 mm1.36 in

Shaft Backing Shoulder Diameter - Backface (db)

 N/A 36 mm1.42 in

Housing Backing Shoulder Diameter - Frontface (Da)

 N/A 58.42 mm2.3 in

Housing Backing Shoulder Diameter - Backface (Db)

 N/A 55.12 mm2.17 in

Cage Location Relative to Backface (Aa)

 N/A 0 mm0 in

Cage Location Relative to Frontface (Ab) 

 N/A 2.8 mm0.11 in

Weight

 N/A 0.30 Kg0.6 lb

Ratings

Dynamic Axial Rating - 90M Revs (Ca90)9 N/A 8210 N1850 lbf

Static Radial Load Rating (C0)

 N/A 51800 N11600 lbf

Factors

G1 Factor

 N/A 13.4

G2 Factor

 N/A 10.7
Geometry Factor (Cg)10 N/A 0.0601
  • 1 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 2 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 3 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 4 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 5 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 6 Negative value indicates effective center inside cone backface.
  • 7 These maximum fillet radii will be cleared by the bearing corners.
  • 8 These maximum fillet radii will be cleared by the bearing corners.
  • 9 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.