Often referred to as snap-ring assemblies, type 2S consist of two basic single-row bearings (type TS). They are supplied complete with inner-ring and outer-ring spacers to give a pre determined bearing setting when assembled. Type 2S have a specified setting range to suit the duty of the application. They have an inner-ring spacer and a snap-ring, which also serves as the outer-ring spacer, to give axial location in a through-bored housing.
Request Information
Unit of Measure

Other Dimensions

Weight

 N/A 0.28 Kg0.63 lb

Width (T)

 N/A 1.5000 in38.100 mm

C - Width

 N/A 1.2300 in31.242 mm

Snap Ring Diameter

 N/A 1.84 in46.81 mm

Snap Ring Width

 N/A 0.28 in7.11 mm
Max Shaft Fillet Radius1 N/A 0.050 in1.270 mm
Max Housing Fillet Radius2 N/A 0.050 in1.27 mm

Shaft Backing Shoulder Diameter - Backface (db)

 N/A 0.98 in25 mm

Housing Backing Shoulder Diameter - Frontface (Da)

 N/A 1.65 in41.90 mm

Key Dimensions

Cone Part Number

 N/A LM11949

Cup Part Number

 N/A LM11910

Inner Spacer Part Number

 N/A K107061R

Outer Spacer Part Number

 N/A K107087R

Design Unit

 N/A Inch

Bore (d)

 N/A 0.7500 in19.050 mm

O.D. (D)

 N/A 1.7810 in45.237 mm
Dynamic Radial Load Rating - 90M Revs (C90) 3 N/A 2280 lbf10100 N
Dynamic Radial Load Rating 2-Row - 90M Revs (C90-2row)4 N/A 3970 lbf17700 N
K Factor 5 N/A 1.94
e Factor 6 N/A 0.3

Ratings

C1 - Dynamic Radial Rating (1 million revolutions)7 N/A 15300 lbf68100 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)8 N/A 1170 lbf5220 N

Factors

Y1 Factor 9 N/A 2.25
Y2 Factor 10 N/A 3.34
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 5 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 6 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 7 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 8 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.