CAD (0) ▾
  • Cart is empty
  1. Request CAD files
Like the TS bearing design, the TSF design consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft. TSF bearings have flanged cups to facilitate axial location and accurately align seals in through-bored housings.
Request Information
Unit of Measure

Specifications

Series

 N/A M716600

Cone Part Number

 N/A JM716649

Cup Part Number

 N/A JM716610-B

Design Unit

 N/A Metric

Cage Material

 N/A Stamped Steel

Related Assembly Number(s)

 N/A JM716649-90B03

Dimensions

d - Bore

 N/A 85 mm3.3465 in

D - Cup Outer Diameter

 N/A 130 mm5.1181 in

D1 - Flange Outer Diameter

 N/A 135.500 mm5.3346 in

B - Cone Width

 N/A 29.000 mm1.1417 in

C - Cup Width

 N/A 24.000 mm0.9449 in

C1 - Cup Flange Width

 N/A 5.558 mm0.2188 in

T1 - Bearing Width to Flange

 N/A 11.557 mm4.550 in

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 3.050 mm0.12 in
r - Cup Backface "To Clear" Radius2 N/A 2.5 mm0.1 in

da - Cone Frontface Backing Diameter

 N/A 92 mm3.62 in

db - Cone Backface Backing Diameter

 N/A 98 mm3.86 in

Da - Cup Frontface Backing Diameter

 N/A 128.02 mm5.04 in

Ab - Cage-Cone Frontface Clearance

 N/A 3 mm0.12 in

Aa - Cage-Cone Backface Clearance

 N/A 1.8 mm0.07 in
a - Effective Center Location3 N/A -0.3 mm-0.01 in

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 41800 N9400 lbf
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 161000 N36300 lbf

C0 - Static Radial Rating

 N/A 245000 N55100 lbf
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 31800 N7150 lbf

Factors

K - Factor7 N/A 1.31
e - ISO Factor8 N/A 0.44
Y - ISO Factor9 N/A 1.35

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 117.1

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 38.4
Cg - Geometry Factor10 N/A 0.13
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.