Batch CAD Cart (0)
  • Cart is empty
Like the TS bearing design, the TSF design consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft. TSF bearings have flanged cups to facilitate axial location and accurately align seals in through-bored housings.
Unit of Measure

Specifications

Series

N/A 9000

Cone Part Number

N/A 09062

Cup Part Number

N/A 09195AB

Design Unit

N/A Inch

Cage Material

N/A Stamped Steel

Dimensions

d - Bore

N/A 0.6250 in15.875 mm

D - Cup Outer Diameter

N/A 1.9380 in49.225 mm

D1 - Flange Outer Diameter

N/A 2.0898 in53.081 mm

B - Cone Width

N/A 0.8480 in21.539 mm

C - Cup Width

N/A 0.5625 in14.288 mm

C1 - Cup Flange Width

N/A 0.1280 in3.251 mm

T1 - Bearing Width to Flange

N/A 0.3468 in8.809 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.03 in0.800 mm
r - Cup Backface "To Clear" Radius2 N/A 0.050 in1.3 mm

da - Cone Frontface Backing Diameter

N/A 0.85 in21.5 mm

db - Cone Backface Backing Diameter

N/A 0.87 in22 mm

Da - Cup Frontface Backing Diameter

N/A 1.85 in46.99 mm

Ab - Cage-Cone Frontface Clearance

N/A 0.06 in1.5 mm

Aa - Cage-Cone Backface Clearance

N/A 0.07 in1.8 mm
a - Effective Center Location3 N/A -0.36 in-9.1 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 2500 lbf11100 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 9630 lbf42800 N

C0 - Static Radial Rating

N/A 9100 lbf40500 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 1140 lbf5050 N

Factors

K - Factor7 N/A 2.2
e - ISO Factor8 N/A 0.27
Y - ISO Factor9 N/A 2.26
Cg - Geometry Factor10 N/A 0.0452
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.
By clicking Submit, you consent to the personal information you provide being used in the manner as described in our Privacy Notice, including access to that information by Timken personnel who may be located outside your home country. In addition, you agree that the CAD drawings are for your personal, one-time use only, and that you will not modify or create any compilation or derivative work using the CAD drawings or distribute or display the CAD drawings on any website or other media.