COMPANY HEADER
CAD (0) ▾
  • Cart is empty
  1. Request CAD files
Terms
Request Information Add to CAD Cart
Like the TS bearing design, the TSF design consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft. TSF bearings have flanged cups to facilitate axial location and accurately align seals in through-bored housings.
Unit of Measure

Specifications

Series

 N/A 16000

Cone Part Number

 N/A 16143

Cup Part Number

 N/A 16284-B

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 1 7/16 in36.513 mm

D - Cup Outer Diameter

 N/A 2.8440 in72.238 mm

D1 - Flange Outer Diameter

 N/A 2.9960 in76.098 mm

B - Cone Width

 N/A 0.8125 in20.638 mm

C - Cup Width

 N/A 0.6250 in15.875 mm

C1 - Cup Flange Width

 N/A 0.1563 in3.970 mm

T1 - Bearing Width to Flange

 N/A 0.3438 in8.733 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.14 in3.600 mm
r - Cup Backface "To Clear" Radius2 N/A 0.030 in0.8 mm

da - Cone Frontface Backing Diameter

 N/A 1.65 in42 mm

db - Cone Backface Backing Diameter

 N/A 1.91 in48.5 mm

Da - Cup Frontface Backing Diameter

 N/A 2.74 in69.60 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.07 in1.8 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.02 in0.5 mm
a - Effective Center Location3 N/A -0.16 in-4.1 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 3300 lbf14700 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 12700 lbf56600 N

C0 - Static Radial Rating

 N/A 14800 lbf65800 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 2270 lbf10100 N

Factors

K - Factor7 N/A 1.45
e - ISO Factor8 N/A 0.4
Y - ISO Factor9 N/A 1.49

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 20.3

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 10.6
Cg - Geometry Factor10 N/A 0.0707
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.