Batch CAD Cart (0)
  • Cart is empty
Like the TS bearing design, the TSF design consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft. TSF bearings have flanged cups to facilitate axial location and accurately align seals in through-bored housings.
Unit of Measure

Specifications

Series

N/A 290000

Cone Part Number

N/A EE291175

Cup Part Number

N/A 291750-B

Design Unit

N/A Inch

Cage Material

N/A Stamped Steel

Dimensions

d - Bore

N/A 11.7500 in298.450 mm

D - Cup Outer Diameter

N/A 17.5 in444.5 mm

D1 - Flange Outer Diameter

N/A 17.9960 in457.098 mm

B - Cone Width

N/A 2.4375 in61.913 mm

C - Cup Width

N/A 1.5625 in39.688 mm

C1 - Cup Flange Width

N/A 0.5000 in12.700 mm

T1 - Bearing Width to Flange

N/A 1.4375 in36.513 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.310 in7.900 mm
r - Cup Backface "To Clear" Radius2 N/A 0.06 in1.5 mm

da - Cone Frontface Backing Diameter

N/A 12.6 in320 mm

db - Cone Backface Backing Diameter

N/A 13.07 in332 mm

Da - Cup Frontface Backing Diameter

N/A 16.87 in428.50 mm

Ab - Cage-Cone Frontface Clearance

N/A 0.34 in8.6 mm

Aa - Cage-Cone Backface Clearance

N/A 0.4 in10.2 mm
a - Effective Center Location3 N/A 0.3 in7.6 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 51700 lbf230000 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 199000 lbf887000 N

C0 - Static Radial Rating

N/A 312000 lbf1390000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 33400 lbf149000 N

Factors

K - Factor7 N/A 1.55
e - ISO Factor8 N/A 0.38
Y - ISO Factor9 N/A 1.59

G1 - Heat Generation Factor (Roller-Raceway)

N/A 1580

G2 - Heat Generation Factor (Rib-Roller End)

N/A 245
Cg - Geometry Factor10 N/A 0.156
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.
By clicking Submit, you consent to the personal information you provide being used in the manner as described in our Privacy Notice, including access to that information by Timken personnel who may be located outside your home country. In addition, you agree that the CAD drawings are for your personal, one-time use only, and that you will not modify or create any compilation or derivative work using the CAD drawings or distribute or display the CAD drawings on any website or other media.