2TS-DM assemblies are comprised of two single-row bearings with abutting back facing inner rings and an outer ring spacer with lubricating holes is typical. These are generally used at fixed positions on rotating shaft applications.

Design Attributes:
  • Two single row bearings, with or without a spacer
  • When spacers are used, bearing is furnished as a preset, matched assembly
  • Spacers available with or without lubricant grooves and holes
    • Unit of Measure

    Key Dimensions

    Cone Part Number

    		 N/A 19138

    Cup Part Number

    		 N/A 19268

    Outer Spacer Part Number

    		 N/A Y2S-19268

    Bore (d)

    		 N/A 1.3770 in34.976 mm

    O.D. (D)

    		 N/A 2.6875 in68.263 mm

    Width (T)

    		 N/A 1.2500 in31.750 mm
    Dynamic Radial Load Rating - 1M Revs (C1)1 N/A 19800 lbf88300 N
    Dynamic Radial Load Rating - 90M Revs (C90) 2 N/A 2960 lbf13100 N
    Dynamic Radial Load Rating 2-Row - 90M Revs (C90-2row)3 N/A 5150 lbf22900 N
    e Factor 4 N/A 0.44
    K Factor 5 N/A 1.31

    Other Dimensions

    Weight

    		 N/A 12.25 Kg26.99 lb

    Width (B)

    		 N/A 1.3008 in33.04 mm
    Max Shaft Fillet Radius6 N/A 0.01 in0.3 mm
    Max Housing Fillet Radius7 N/A 0.06 in1.52 mm

    Shaft Backing Shoulder Dia. - Backface (db)

    		 N/A 1.67 in42.5 mm

    Housing Backing Shoulder Dia. - Frontface (Da)

    		 N/A 2.60 in66.00 mm

    Ratings

    Dynamic Axial Rating - 90M Revs (Ca90)8 N/A 2250 lbf10000 N

    Factors

    Y1 Factor 9 N/A 1.52
    Y2 Factor 10 N/A 2.26
    • 1 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
    • 2 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
    • 3 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
    • 4 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
    • 5 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
    • 6 These maximum fillet radii will be cleared by the bearing corners.
    • 7 These maximum fillet radii will be cleared by the bearing corners.
    • 8 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
    • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
    • 10 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.