Batch CAD Cart (0)
  • Cart is empty
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

N/A 03000

Cone Part Number

N/A 03062

Cup Part Number

N/A 03157X

Design Unit

N/A Inch

Cage Material

N/A Stamped Steel

Dimensions

d - Bore

N/A 0.6250 in15.875 mm

D - Cup Outer Diameter

N/A 1.5748 in40 mm

B - Cone Width

N/A 0.5780 in14.681 mm

C - Cup Width

N/A 0.4375 in11.113 mm

T - Bearing Width

N/A 0.5626 in14.290 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.050 in1.270 mm
r - Cup Backface "To Clear" Radius2 N/A 0.06 in1.52 mm

da - Cone Frontface Backing Diameter

N/A 0.79 in20 mm

db - Cone Backface Backing Diameter

N/A 0.85 in21.5 mm

Da - Cup Frontface Backing Diameter

N/A 1.48 in37.59 mm

Db - Cup Backface Backing Diameter

N/A 1.34 in34.04 mm

Ab - Cage-Cone Frontface Clearance

N/A 0.08 in2 mm

Aa - Cage-Cone Backface Clearance

N/A -0.01 in-0.3 mm
a - Effective Center Location3 N/A -0.2 in-5.1 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 1400 lbf6230 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 5400 lbf24000 N

C0 - Static Radial Rating

N/A 4780 lbf21300 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 745 lbf3310 N

Factors

K - Factor7 N/A 1.88
e - ISO Factor8 N/A 0.31
Y - ISO Factor9 N/A 1.93

G1 - Heat Generation Factor (Roller-Raceway)

N/A 4.2

G2 - Heat Generation Factor (Rib-Roller End)

N/A 4
Cg - Geometry Factor10 N/A 0.0384
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.
By clicking Submit, you consent to the personal information you provide being used in the manner as described in our Privacy Notice, including access to that information by Timken personnel who may be located outside your home country. In addition, you agree that the CAD drawings are for your personal, one-time use only, and that you will not modify or create any compilation or derivative work using the CAD drawings or distribute or display the CAD drawings on any website or other media.