Batch CAD Cart (0)
  • Cart is empty
This is the most basic and most widely used type of tapered roller bearing. It consists of two main separable parts: the cone (inner ring) assembly and the cup (outer ring). It is typically mounted in opposing pairs on a shaft.
Unit of Measure

Specifications

Series

N/A 11500

Cone Part Number

N/A 11590

Cup Part Number

N/A 11520

Design Unit

N/A Inch

Cage Material

N/A Stamped Steel

Dimensions

d - Bore

N/A 0.6250 in15.875 mm

D - Cup Outer Diameter

N/A 1.6875 in42.863 mm

B - Cone Width

N/A 0.5625 in14.288 mm

C - Cup Width

N/A 0.3750 in9.525 mm

T - Bearing Width

N/A 0.5625 in14.288 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.06 in1.520 mm
r - Cup Backface "To Clear" Radius2 N/A 0.06 in1.52 mm

da - Cone Frontface Backing Diameter

N/A 0.89 in22.5 mm

db - Cone Backface Backing Diameter

N/A 0.96 in24.5 mm

Da - Cup Frontface Backing Diameter

N/A 1.59 in40.39 mm

Db - Cup Backface Backing Diameter

N/A 1.36 in34.54 mm

Ab - Cage-Cone Frontface Clearance

N/A 0.05 in1.3 mm

Aa - Cage-Cone Backface Clearance

N/A 0.04 in1 mm
a - Effective Center Location3 N/A -0.05 in-1.3 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 1100 lbf4870 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 4230 lbf18800 N

C0 - Static Radial Rating

N/A 3920 lbf17400 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 1320 lbf5860 N

Factors

K - Factor7 N/A 0.83
e - ISO Factor8 N/A 0.7
Y - ISO Factor9 N/A 0.85

G1 - Heat Generation Factor (Roller-Raceway)

N/A 3.4

G2 - Heat Generation Factor (Rib-Roller End)

N/A 4.63
Cg - Geometry Factor10 N/A 0.0465
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.
By clicking Submit, you consent to the personal information you provide being used in the manner as described in our Privacy Notice, including access to that information by Timken personnel who may be located outside your home country. In addition, you agree that the CAD drawings are for your personal, one-time use only, and that you will not modify or create any compilation or derivative work using the CAD drawings or distribute or display the CAD drawings on any website or other media.