COMPANY HEADER
CAD (0) ▾
  • Cart is empty
  1. Request CAD files
Terms
Request Information Add to CAD Cart

Key Features

  • Available in single, double and multi-row configurations, as well as proprietary sizes
  • Designed in collaboration with OE engineers to design, engineer and test bearings for premium performance in many applications
  • Power dense designs allow for heavier loads and can help extend bearing life
  • Optimized internal geometry lowers torque and operating temperatures to extend lubrication system life
  • Can be designed to withstand high-corrosive, high-temperature and vacuum or low-lubrication environments with proprietary enhancements
Unit of Measure

Key Dimensions

Cone Part Number

 N/A 39585P

Cup Part Number

 N/A 39521P

Bore (d)

 N/A 2.5 in63.5 mm

O.D. (D)

 N/A 4.4375 in112.712 mm

Width (T)

 N/A 1.1875 in30.165 mm
Dynamic Radial Load Rating - 1M Revs (C1)1 N/A 44500 lbf198000 N
Dynamic Radial Load Rating - 90M Revs (C90) 2 N/A 11500 lbf51300 N
e Factor3 N/A 0.34
K Factor4 N/A 1.72

Other Dimensions

Inner Ring Width (B)

 N/A 1.1875 in30.163 mm

Outer Ring Width (C)

 N/A 0.8268 in21.001 mm
Effective Center Location5 N/A -0.26 in-6.6 mm
Max Shaft Fillet Radius6 N/A 0.14 in3.6 mm
Max Housing Fillet Radius7 N/A 0.06 in1.5 mm

Shaft Backing Shoulder Diameter - Frontface (da)

 N/A 2.87 in73 mm

Shaft Backing Shoulder Diameter - Backface (db)

 N/A 3.11 in79 mm

Housing Backing Shoulder Diameter - Frontface (Da)

 N/A 4.21 in107 mm

Cage Location Relative to Backface (Aa)

 N/A 0.05 in1.3 mm

Cage Location Relative to Frontface (Ab)

 N/A 0.13 in3.3 mm

Ratings

Dynamic Axial Rating - 90M Revs (Ca90)8 N/A 6700 lbf29800 N

Static Radial Load Rating (C0)

 N/A 50300 lbf224000 N

Factors

G1 Factor

 N/A 84.3

G2 Factor

 N/A 23.7
Geometry Factor (Cg)9 N/A 0.107
  • 1 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 2 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 3 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 4 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 5 Negative value indicates effective center inside cone backface.
  • 6 These maximum fillet radii will be cleared by the bearing corners.
  • 7 These maximum fillet radii will be cleared by the bearing corners.
  • 8 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 9 Geometry constant for Lubrication Life Adjustment Factor a3l.