Montage of Timken Bearing Products
Batch CAD Cart (0) ▾
  • Cart is empty
  1. Click Here for Batch Download
Request Information Add to CAD Cart
Tapered Roller Bearings - TSL (DUO-FACE® Plus Seal) Imperial
Unit of Measure

Specifications

Series

 N/A LM29700

Cone Part Number

 N/A LM29748

Cup Part Number

 N/A LM29710

Seal Part Number

 N/A LM29700LA

Design Unit

 N/A Inch

Cage Material

 N/A Stamped Steel

Dimensions

d - Bore

 N/A 1 1/2 in38.1 mm

D - Cup Outer Diameter

 N/A 2.5625 in65.088 mm

B - Cone Width

 N/A 0.7200 in18.288 mm

C - Cup Width

 N/A 0.5500 in13.970 mm

T - Bearing Width

 N/A 0.71 in18.034 mm

T1 - Total Width

 N/A 0.7850 in19.940 mm

Abutment and Fillet Dimensions

R - Cone Backface "To Clear" Radius1 N/A 0.14 in3.560 mm
r - Cup Backface "To Clear" Radius2 N/A 0.050 in1.27 mm

da - Cone Frontface Backing Diameter

 N/A 1.67 in42.5 mm

db - Cone Backface Backing Diameter

 N/A 1.93 in49 mm

Da - Cup Frontface Backing Diameter

 N/A 2.46 in62.00 mm

Db - Cup Backface Backing Diameter

 N/A 2.32 in58.93 mm

Ab - Cage-Cone Frontface Clearance

 N/A 0.07 in1.8 mm

Aa - Cage-Cone Backface Clearance

 N/A 0.01 in0.3 mm
a - Effective Center Location3 N/A -0.16 in-4.1 mm

Basic Load Ratings

C90 - Dynamic Radial Rating (90 million revolutions)4 N/A 2830 lbf12600 N
C1 - Dynamic Radial Rating (1 million revolutions)5 N/A 10900 lbf48600 N

C0 - Static Radial Rating

 N/A 13600 lbf60300 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)6 N/A 1610 lbf7170 N

Factors

K - Factor7 N/A 1.76
e - ISO Factor8 N/A 0.33
Y - ISO Factor9 N/A 1.8
Y1 - ISO Factor10 N/A 2.03
Y2 - ISO Factor11 N/A 3.02

G1 - Heat Generation Factor (Roller-Raceway)

 N/A 20.4

G2 - Heat Generation Factor (Rib-Roller End)

 N/A 15
Cg - Geometry Factor12 N/A 0.0666
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Negative value indicates effective center inside cone backface.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 5 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 6 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 7 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 8 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 11 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 12 Geometry constant for Lubrication Life Adjustment Factor a3l.