The Timken Company
The Timken Company
4500 Mt Pleasant St. NW
N. Canton, OH 44720
Phone: (234) 262-3000
E-Mail: CustomerCAD@timken.com • Web site: www.timken.com
Print Back

Key Features

  • Available in single, double and multi-row configurations, as well as proprietary sizes
  • Designed in collaboration with OE engineers to design, engineer and test bearings for premium performance in many applications
  • Power dense designs allow for heavier loads and can help extend bearing life
  • Optimized internal geometry lowers torque and operating temperatures to extend lubrication system life
  • Can be designed to withstand high-corrosive, high-temperature and vacuum or low-lubrication environments with proprietary enhancements
Unit of Measure

Key Dimensions

Cone Part Number

 N/A 745

Cup Part Number

 N/A 742-B

Bore (d)

 N/A 2.3595 in59.931 mm

O.D. (D)

 N/A 5.9090 in150.089 mm

Width (T)

 N/A 0.625 in15.875 mm
Dynamic Radial Load Rating - 1M Revs (C1) 1 N/A 71400 lbf318000 N
Dynamic Radial Load Rating - 90M Revs (C90) 2 N/A 18500 lbf82400 N
e Factor3 N/A 0.33
K Factor 4 N/A 1.8

Series

 N/A 745
Y Factor 5 N/A 1.84

Other Dimensions

Inner Ring Width (B)

 N/A 1.8375 in46.673 mm

Outer Ring Width (C)

 N/A 1.4375 in36.513 mm

Outer Ring Flange O.D.(D1)

 N/A 6.2170 in157.912 mm

Outer Ring Flange Width (C2)

 N/A 0.3125 in7.938 mm
Effective Center Location6 N/A -0.47 in-11.9 mm
Max Shaft Fillet Radius7 N/A 0.14 in3.6 mm

Shaft Backing Shoulder Diameter - Frontface (da)

 N/A 2.95 in75 mm

Shaft Backing Shoulder Diameter - Backface (db)

 N/A 3.19 in81 mm

Housing Backing Shoulder Diameter - Frontface (Da)

 N/A 5.64 in143.26 mm
Max Housing Fillet Radius8 N/A 0.13 in3.3 mm

Cage Location Relative to Frontface (Ab) 

 N/A 0.08 in2 mm

Cage Location Relative to Backface (Aa)

 N/A 0.05 in1.3 mm

Weight

 N/A 9.7 lb4.4 Kg

Ratings

Dynamic Axial Rating - 90M Revs (Ca90)9 N/A 10300 lbf45900 N

Static Radial Load Rating (C0)

 N/A 93800 lbf417000 N

Factors

G1 Factor

 N/A 159.6

G2 Factor

 N/A 26.3
Geometry Factor (Cg) 10 N/A 0.0898
  • 1 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 2 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 3 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 4 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 5 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 6 Negative value indicates effective center inside cone backface.
  • 7 These maximum fillet radii will be cleared by the bearing corners.
  • 8 These maximum fillet radii will be cleared by the bearing corners.
  • 9 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.