The Timken Company
The Timken Company
4500 Mt Pleasant St. NW
N. Canton, OH 44720
Phone: (234) 262-3000
E-Mail: CustomerCAD@timken.com • Web site: www.timken.com
Print Back

Key Features

  • Available in single, double and multi-row configurations, as well as proprietary sizes
  • Designed in collaboration with OE engineers to design, engineer and test bearings for premium performance in many applications
  • Power dense designs allow for heavier loads and can help extend bearing life
  • Optimized internal geometry lowers torque and operating temperatures to extend lubrication system life
  • Can be designed to withstand high-corrosive, high-temperature and vacuum or low-lubrication environments with proprietary enhancements
Unit of Measure

Key Dimensions

Cone Part Number

 N/A HM535349

Cup Part Number

 N/A HM535310-B

Bore (d)

 N/A 6.75 in171.45 mm

O.D. (D)

 N/A 10.25 in260.350 mm

Width (T)

 N/A 1 in25.4 mm
Dynamic Radial Load Rating - 1M Revs (C1) 1 N/A 147000 lbf654000 N
Dynamic Radial Load Rating - 90M Revs (C90) 2 N/A 38100 lbf169000 N
e Factor3 N/A 0.4
K Factor 4 N/A 1.45

Series

 N/A HM535300
Y Factor 5 N/A 1.49

Other Dimensions

Inner Ring Width (B)

 N/A 2.625 in66.675 mm

Outer Ring Width (C)

 N/A 2.0625 in52.388 mm

Outer Ring Flange O.D.(D1)

 N/A 10.6840 in271.374 mm

Outer Ring Flange Width (C2)

 N/A 0.4375 in11.113 mm
Effective Center Location6 N/A -0.34 in-8.6 mm
Max Shaft Fillet Radius7 N/A 0.14 in3.6 mm

Shaft Backing Shoulder Diameter - Frontface (da)

 N/A 7.4 in186.1 mm

Shaft Backing Shoulder Diameter - Backface (db)

 N/A 7.56 in192 mm

Housing Backing Shoulder Diameter - Frontface (Da)

 N/A 9.86 in249.94 mm
Max Housing Fillet Radius8 N/A 0.13 in3.3 mm

Cage Location Relative to Frontface (Ab) 

 N/A 0.13 in3.3 mm

Cage Location Relative to Backface (Aa)

 N/A 0.21 in5.3 mm

Weight

 N/A 28.1 lb12.7 Kg

Ratings

Dynamic Axial Rating - 90M Revs (Ca90)9 N/A 26200 lbf117000 N

Static Radial Load Rating (C0)

 N/A 265000 lbf1180000 N

Factors

G1 Factor

 N/A 750

G2 Factor

 N/A 116
Geometry Factor (Cg) 10 N/A 0.126
  • 1 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 2 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 3 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 4 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 5 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 6 Negative value indicates effective center inside cone backface.
  • 7 These maximum fillet radii will be cleared by the bearing corners.
  • 8 These maximum fillet radii will be cleared by the bearing corners.
  • 9 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.