The Timken Company
The Timken Company
4500 Mt Pleasant St. NW
N. Canton, OH 44720
Phone: (234) 262-3000
E-Mail: CustomerCAD@timken.com • Web site: www.timken.com
Print Back

Key Features

  • Available in single, double and multi-row configurations, as well as proprietary sizes
  • Designed in collaboration with OE engineers to design, engineer and test bearings for premium performance in many applications
  • Power dense designs allow for heavier loads and can help extend bearing life
  • Optimized internal geometry lowers torque and operating temperatures to extend lubrication system life
  • Can be designed to withstand high-corrosive, high-temperature and vacuum or low-lubrication environments with proprietary enhancements
Unit of Measure

Key Dimensions

Cone Part Number

 N/A LL582949

Cup Part Number

 N/A LL582910-B

Bore (d)

 N/A 29 in736.6 mm

O.D. (D)

 N/A 32.5 in825.5 mm

Width (T)

 N/A 0.5 in12.7 mm
Dynamic Radial Load Rating - 1M Revs (C1) 1 N/A 95300 lbf424000 N
Dynamic Radial Load Rating - 90M Revs (C90) 2 N/A 24700 lbf110000 N
e Factor3 N/A 0.4
K Factor 4 N/A 1.47

Series

 N/A LL582900
Y Factor 5 N/A 1.51

Other Dimensions

Inner Ring Width (B)

 N/A 1.25 in31.75 mm

Outer Ring Width (C)

 N/A 1 in25.4 mm

Outer Ring Flange O.D.(D1)

 N/A 32.8124 in833.435 mm

Outer Ring Flange Width (C2)

 N/A 0.25 in6.35 mm
Effective Center Location6 N/A 3.42 in86.9 mm
Max Shaft Fillet Radius7 N/A 0.14 in3.6 mm

Shaft Backing Shoulder Diameter - Frontface (da)

 N/A 29.65 in753.1 mm

Shaft Backing Shoulder Diameter - Backface (db)

 N/A 29.65 in753.1 mm

Housing Backing Shoulder Diameter - Frontface (Da)

 N/A 31.87 in809.5 mm
Max Housing Fillet Radius8 N/A 0.13 in3.3 mm

Cage Location Relative to Frontface (Ab) 

 N/A 0.09 in2.3 mm

Cage Location Relative to Backface (Aa)

 N/A -0.05 in-1.3 mm

Weight

 N/A 0.5 lb0.20 Kg

Ratings

Dynamic Axial Rating - 90M Revs (Ca90)9 N/A 16800 lbf74800 N

Static Radial Load Rating (C0)

 N/A 291000 lbf1300000 N

Factors

Geometry Factor (Cg) 10 N/A 0.244
  • 1 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 2 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 3 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 4 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 5 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 6 Negative value indicates effective center inside cone backface.
  • 7 These maximum fillet radii will be cleared by the bearing corners.
  • 8 These maximum fillet radii will be cleared by the bearing corners.
  • 9 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 10 Geometry constant for Lubrication Life Adjustment Factor a3l.