Often referred to as snap-ring assemblies, type 2S consist of two basic single-row bearings (type TS). They are supplied complete with inner-ring and outer-ring spacers to give a pre determined bearing setting when assembled. Type 2S have a specified setting range to suit the duty of the application. They have an inner-ring spacer and a snap-ring, which also serves as the outer-ring spacer, to give axial location in a through-bored housing.
Request Information
Unit of Measure

Other Dimensions

Weight

 N/A 1.84 Kg4.08 lb

Width (T)

 N/A 1.9502 in49.535 mm

C - Width

 N/A 1.7002 in43.185 mm

Snap Ring Diameter

 N/A 4.57 in116.10 mm

Snap Ring Width

 N/A 0.22 in5.54 mm
Max Shaft Fillet Radius1 N/A 0.03 in0.800 mm
Max Housing Fillet Radius2 N/A 0.050 in1.27 mm

Shaft Backing Shoulder Diameter - Backface (db)

 N/A 2.76 in70 mm

Housing Backing Shoulder Diameter - Frontface (Da)

 N/A 4.15 in105.40 mm

Key Dimensions

Cone Part Number

 N/A 392

Cup Part Number

 N/A 394A

Inner Spacer Part Number

 N/A K444667R

Outer Spacer Part Number

 N/A K444668R

Design Unit

 N/A Inch

Bore (d)

 N/A 2.4375 in61.913 mm

O.D. (D)

 N/A 4.3307 in110.000 mm
Dynamic Radial Load Rating - 90M Revs (C90) 3 N/A 5760 lbf25600 N
Dynamic Radial Load Rating 2-Row - 90M Revs (C90-2row)4 N/A 10000 lbf44600 N
K Factor 5 N/A 1.45
e Factor 6 N/A 0.4

Ratings

C1 - Dynamic Radial Rating (1 million revolutions)7 N/A 38700 lbf172000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)8 N/A 3970 lbf17600 N

Factors

Y1 Factor 9 N/A 1.68
Y2 Factor 10 N/A 2.5
  • 1 These maximum fillet radii will be cleared by the bearing corners.
  • 2 These maximum fillet radii will be cleared by the bearing corners.
  • 3 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 4 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 5 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 6 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 7 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 8 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.