TNA bearings are similar to the TDO, but the inner race narrow faces are extended to abut and eliminate the need for a separate inner race spacer. Supplied with an in-built clearance to give a standard setting range, these bearings provide a solution for many fixed or floating bearing applications where simplicity of assembly is required.

Design Attributes:
  • Double cup and two single cones
  • Internal bearing clearance controlled by extending the front faces of the cones so they contact each other
  • SW variation features chamfers in the bores at the front faces of the two single cones to form a lubrication groove
  • SE variation features a backface rib design to accommodate radial lip seals or stamped closure
Request Information
Unit of Measure

Key Dimensions

Cone Part Number

 N/A NA221027SW

Cup Part Number

 N/A 221576CD

Design Unit

 N/A Inch

Bore (d)

 N/A 10.2500 in260.350 mm

O.D. (D)

 N/A 15.75 in400.05 mm
Dynamic Radial Load Rating - 90M Revs (C90) 1 N/A 48200 lbf215000 N
Dynamic Radial Load Rating 2-Row - 90M Revs (C90-2row)2 N/A 84000 lbf374000 N
K Factor 3 N/A 1.48
e Factor 4 N/A 0.39

Other Dimensions

T - Bearing Width across Cones

 N/A 5.75 in146.05 mm
Max Shaft Fillet Radius5 N/A 0.25 in6.4 mm
Max Housing Fillet Radius6 N/A 0.06 in1.5 mm

Outer Ring Width (C)

 N/A 4.25 in107.95 mm

Shaft Backing Shoulder Diameter - Backface (db)

 N/A 11.42 in290 mm

Housing Backing Shoulder Diameter - Frontface (Da)

 N/A 14.65 in372.1 mm

Weight

 N/A 129.541 lb58.77 Kg

Ratings

C1 - Dynamic Radial Rating (1 million revolutions)7 N/A 324000 lbf1440000 N
Ca90 - Dynamic Thrust Rating (90 million revolutions)8 N/A 32600 lbf145000 N

Factors

Y1 Factor 9 N/A 1.71
Y2 Factor 10 N/A 2.55
  • 1 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values.
  • 2 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 3 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 4 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 5 These maximum fillet radii will be cleared by the bearing corners.
  • 6 These maximum fillet radii will be cleared by the bearing corners.
  • 7 Based on 1 x 106 revolutions L10 life, for the ISO life calculation method.
  • 8 Based on 90 x 106 revolutions L10 life, for The Timken Company life calculation method. C90 and Ca90 are radial and thrust values for a single-row, C90(2) is the two-row radial value.
  • 9 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.
  • 10 These factors apply for both inch and metric calculations. Consult your Timken representative for instruction on use.